Why Understanding Essential Plumbing Skills is Important When Installing a Bathtub
Why Understanding Essential Plumbing Skills is Important When Installing a Bathtub
Blog Article
Are you currently searching for guidance about Installing A Bathtub?
Installing a tub isn't exactly rocket science, but it does call for solid plumbing, woodworking, and also occasionally, tiling skills. Replacing an old bathtub with a brand-new one is additionally a reasonably difficult project. If the old tub is conveniently obtainable, the job can relocate easily; if you have to open a wall surface to get rid of the old bathtub and position the brand-new bathtub, the job is much harder. In either case, the task is within a home handyman's skills, although you will certainly require an assistant to move out the old bathtub and embeded in the brand-new one. Make sure you have certified yourself for the work and are comfortable attempting it. Rather than employing a specialist to take control of a halfway-completed task, it is better to consider using one before you begin. Opportunities are you might need an expert plumber to make tube connections.
This short article will certainly assist you install a brand-new bathtub in your washroom if you have already acquired a new bathtub and also don't need to transform the arrangement of your previous water pipes.
Your devices and material checklist ought to consist of the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you ought to do is detach the supply of water. After doing so, switch on the faucets to drain pipes any water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly problematic because of the limited gain access to that is commonly the case.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the taps. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been removed, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary taps from turning during this procedure. When the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing compound.
Before going on to fit the new faucets, compare the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic port to prevent damage to the string. One end of the connector fits on the plastic tail of the tap and the other end gives a link to the existing supply pipes.
If you need to fit a monobloc, then you will certainly call for decreasing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, position the tap in the placing hole in the bath/basin guaranteeing that the washers remain in place in between the tap and also the sink. Secure the tap in place with the maker offered backnut. Once the tap is safely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical tap ports. The former kind should be attached to the faucet finishes first, tightening up only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Mounting the Bathtub
Making use of the two wooden boards under its feet, position the bath tub in the required setting. The wood boards are handy in evenly spreading the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four tiny factors.
The following objective is to ensure that the bath tub is leveled all round. This can be attained by inspecting the level as well as readjusting the feet on the tub up until the spirit level checks out level.
To install faucets, fit all-time low of the furthest flexible faucet adapter to the ideal supply pipe by making a compression sign up with; after that do the exact same for the various other tap.
Activate the water supply as well as examine all joints and brand-new pipework for leakages and also tighten them if needed. Fill the bath tub as well as also inspect the overflow electrical outlet as well as the regular outlet for leaks.
Lastly, fix the bath paneling as explained in the manufacturer's user's manual. Tiling and also sealing around the bath tub should wait until the bathtub has actually been made use of a minimum of once as this will certainly settle it into its final setting.
Getting ready for the Installment
To start with, the sustaining structure supplied with the bath needs to be fitted (if needed) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is necessary to see to it that if the tap comes with a plastic washer, it is fitted between the bath and the faucets. On a plastic bath, it is additionally sensible to fit a supporting plate under the taps system to prevent pressure on the bathtub.
Fit the flexible tap connectors to the bottom of the two faucets utilizing 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet through the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make certain you use every one of the provided washers.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom should currently prepare to be fitted in its final placement.
Tiling Around the Tub
In the location where the bath meets the tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to split an inflexible seal, creating the water to pass through the wall surface between the bath and the tiling, leading to difficulties with moisture and also feasible leakages to the ceiling listed below.
You can select from a variety of coloured sealants to blend in your fixtures and also installations. They are marketed in tubes as well as cartridges, and can securing voids approximately a size of 3mm (1/8 inch). If you have a larger space to load, you can load it with spins of soaked paper or soft rope. Keep in mind to always fill the bathtub with water before securing, to allow for the motion experienced when the tub remains in use. The sealant can split fairly early if you do not take into consideration this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also quickly offered on the marketplace. It is suggested to fit the ceramic tiles using waterproof or waterproof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy reading up on Tools You Need to Install a New Bathtub ? Place feedback directly below. We will be glad to see your views about this blog. We hope that you come back again soon. Be sure to set aside a second to promote this post if you appreciated it. We cherish reading our article about How to Install a Bathtub Yourself.
Quality commitment here. Report this page